![]() ![]() Save yourself some cash and try to do it yourselfĬalling in the plumber for such a basic job can seem like a waste of money. If the water is now running correctly and the faucet is no longer leaking, you have successfully completed the repair job. The next step is to turn the water back on and test the faucet to see if the water runs the way it should. With the handle firmly attached and screwed back into place, you can replace the cap that covers it. Replace the stem assembly and tighten it with the adjustable wrench, replace the escutcheon and screw it back into place as required and then screw the handle back into place. Once you have replaced the washer and checked and replaced the seat as necessary, it’s time to put everything back in place. To remove the seat, you need to use a seat wrench, a special kind of tool made for this purpose. If you find any signs of damage to the seat, you will need to remove it and replace it. The seat is the part that is in contact with the washer, and it may become damaged either as the washer wears away or through corrosion.Ī damaged seat may cause a leak itself, and it can also quickly damage the new washer you have just fitted, causing the leak to return.įor these reasons, before you replace the stem assembly with the new washer installed, you should also check the seat for any signs of damage. This way, they will be able to find the one you need.Īnother possible reason why you might have a leak is that the seat is damaged. If you do this, it’s a good idea to take the old one with you so you can show the staff in the store. However, if you don’t have one, you will need to go to the hardware store to buy one. This is an easy job – you just unscrew the washer screw, remove the washer, put a new one in and replace the screw. If you have spare washers, simply go ahead and put a new one on. If the washer is the culprit, you need to change it. If it needs to be replaced, it should be quite obvious – an old washer will be hardened and deformed, and this is what lets the water drip through, causing the leak. When you remove the stem assembly, the first thing you can do is check the washer on the end. The most likely reason for a faucet to start leaking is that the washer needs to be replaced. You can use an adjustable wrench to remove stem assembly. This is the part you need to reach to fix the leak. With the escutcheon out of the way, you now have access to the stem assembly. Depending on your faucet, you may need to unscrew it, or you may be able to simply twist it off. The next step is to remove the escutcheon, the plate that covers the hole in the wall. If it still refuses to move, you might need to resort to using a handle puller, a special tool that is designed for this purpose. Instead, a couple of tricks that might help include warming it with hot air from a hairdryer or pouring boiling water over it. If it doesn’t want to come off, don’t force it – you might break it. Depending on how old your faucet is, this part can be a little tricky since corrosion and water deposits can cause the handle to fuse to the stem. Unscrew the screw and place it with the cap so you don’t lose it.Īfter removing the screw, you can then remove the handle. You now need to remove this with a screwdriver. Once the cap has been removed, you will see the screw inside the faucet handle that holds the handle in place. Place it somewhere safe where you will be able to find it again later. To do this, you can either use a small pocketknife or a slotted screwdriver.įirst, open the faucet all the way to drain any water (the same as if you wanted to run the water) and then pry the cap off with your chosen tool. The next step is to pry off the cap that covers the faucet handle screw. If not, you will have to turn off the water supply to your whole house before you can move to the next step – there should be a lever near the water meter that will allow you to do this. There may be a simple valve in your house or apartment that allows you to turn off the water to the bathtub. If you forget to do it, you will end up spraying water everywhere when you start to remove the faucet from its fitting. The first step when fixing a leaky bathtub faucet is shutting off the water supply. However, for a freestanding bathtub with a separate faucet, the steps would be slightly different. Here are the steps for how to do it – and these steps apply to most kinds of bathtub, including walk-in bathtubs, corner bathtubs and so on. The most common reason for a leaky faucet is an old washer that needs to be replaced. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |